How To Remove The Brake Fluid Reservoir From The Master Cylinder?

If you ever take a close look at your vehicle’s brake, you will find a reservoir. This tank is made with plastic, and its task is to feed brake fluid to the master cylinder. In case there are cracks or other deformations in this component, or it gets damaged. This step will help you to escape the threats of contamination or fluid leaks. In such situations, it becomes inevitable to detach the master cylinder for examination and, consequently, replace the unit if the situation demands. It would help if you did this by positioning the cylinder in a fixed spot so that no damages are caused to the brake fluid tank. 

Your guide to eliminate the brake fluid tank from the Main cylinder 

It will not be a stiff task to accomplish this assignment if you are ready to invest a little effort and time. These assignments call for excitement and enjoyment as you acquire the knowledge to fix your vehicle’s issues. It will spare you from the need and compulsion to call for professional assistance each time your vehicle needs some care and repair. Here is your guide to detach the Main cylinder from the fluid tank. 

The work starts as you lift the vehicle hood, pooping it up to reach the automobile engine’s compartment. Now, you need to find the Main Cylinder. You will find it as a plastic or metallic part, lying on the side of the driver. Usually, it lies close to the firewall. Consequently, you need to connect the brake lines with the four hoses.

After you have completed all the instructions stated above, it’ is time to clamp a vise on the body flange. Now, keep on tightening the vice gradually. At the next step, you require putting a bar on the gap between the Master cylinder and Fluid reservoir. Please ensure that the reservoir body is at a fair distance from the main cylinder. Did you found rubber-made grommets that keep the cylinder attached to the reservoir? If yes, you need to eliminate this component. 

You should inspect the brake system thoroughly while eliminating the master cylinder. 

It is a well-known fact to all car owners that regular inspection of the car components is the best way to ensure its appropriate maintenance. While you work on the master cylinder, it is a beautiful opportunity to accomplish this task. The car manual will assist you in identifying all the components of the brake. It would help if you looked around for the fluid reservoir, the sensor level, and the lines. In case you find that some components demand a replacement, you should do that at its earliest. Hiding the dust under the carpet will not do, as it will escalate the cost for more extensive repair and replacements at a later stage.

How to drain out the fluid from the tank? 

The task in this regard is simple, and you can do it yourself within the minimum time. You need to proceed as follows:

  • Eliminate the Tank cap
  • It would help if you drained out the brake fluid from its tank. You may use a turkey buster to accomplish this task. 
  • You need to comply with the prevailing legal code in your area for disposing or recycling the brake fluid. In case you need information or assistance in this context, you should consult with the local authority dealing with hazardous wastes. The authority will be happy to help you in this regard. 

The majority of people find it difficult to detach the connector for the fluid brake sensor. The user manual of your car can guide you to identify this part. Once done, you can eliminate the connector quickly, merely pulling it manually. The car manual will give you detailed guidance in this regard.

Steps for removing the fluid lines 

You should start this task with a line wrench in your hand. Now, use the tool to loosen the fluid lines of your car brake. Going in an anti-clockwise motion, keep twisting the wrench till you have successfully eliminated all the lines. It would be best if you took a towel in hand to clean the fluid leaking out of the reservoir. 

It is a simple task to detach the master cylinder. It would be best if you are looking for the mounting bolts. Consequently, it would be best if you eliminated these mounts. One can serve this purpose with a socket wrench. If you are finding it tough to locate the mounts, you should refer to the car manual. Subsequently, you can detach the master cylinder manually. 

Thus, working on the master cylinder is not a mammoth task to undertake. You can accomplish this task easily, putting in the least effort, and within the minimum time. It allows you to escape the threat to incur expenses on professional assistance each time your car shows a few malfunctions.